Ubiquiti UA-SK-GATE UniFi Gate Access Starter Kit

UA-Hub-Gate

Mechanical

Dimensions

175 x 126 x 26 mm (6.9 x 5 x 1")

Weight

460 g (1 lb)

Enclosure material

Polycarbonate

Mounting

Din-rail (Included)

Hardware

Networking interface

(5) 10/100/1000 Base-T

Power method

PoE++

Max. power consumption

Without PoE output: 22W
With PoE output: 50W

PoE input

50V DC, 1A

PoE output

PoE passthrough, (4) PoE, 50V DC, Max. 28W

Button

(1) Factory-reset

Digital input

Gate exit request, gate position, side door exit request, side door position, emergency

Dry output relay

(2) Operator: rated 30V DC, up to 1A
(1) Aux: rated 30V DC, up to 1A

Powered output relay

Side door lock: 12V DC, up to 1A

Operating environment

Indoor use only with device itself
Outdoor use with waterproof junction box

Ambient operating temperature

-30 to 60° C (-22 to 104° F)

Ambient operating humidity

5 to 90% noncondensing

Certifications

CE, FCC, IC

LEDs

PoE in

Steady white: Pending adoption
Steady blue: Adopted, device is ready
Blinking white/blue: Upgrading firmware

PoE out

Off: Not connected or no data link
Steady white: Connected and data link on

Input terminals

Off: No wire
Steady white: Wire connected
Blinking white: Active signal

Output relays

Off: No wire
Steady white: Wire connected
Blinking white: Relay triggered

UA-Intercom
Mechanical

Dimensions

324.8 x 113.7 x 28.3 mm (12.8 x 4.5 x 1.1")

Weight

Device: 965 g (2.1 lb)
Bracket: 445 g (1 lb)

Enclosure material

Aluminium alloy, UV-stabilized polycarbonate, glass

Mount material

Powder-coated stainless steel

Mounting

Wall mount, adapter to the gooseneck pedestal (Included)
Surface angle mount, flush mount (Optional)
Sunshield kit (Optional)

Weatherproofing

IP65

Hardware

Networking interface

(1) GbE RJ45 port

Connectivity

Bluetooth 4.2
NFC

Power method

PoE
UL 294 Power-limited Class 2 PSU
UL 60950-1/62368-1 LPS/PS2 PSU

Supported voltage range

48V DC

Max. power consumption

13W

ESD/EMP protection

Air: ±15kV, contact: ±8kV

Sensors

Proximity sensor
ALS sensor

Camera

3264 x 2448, 8 MP
H: 79.4°, V: 97.5°, D: 118.2°

Display

177 mm (7") diagonal

Resolution

1024 x 600 (16:9)

Display luminance

Max. 1000 nits (typical)

Touch screen technology

Capacitive multi-touch

Microphone

Yes

Speaker

(1) 4 ohm, 2W

LEDs

(1) LCM low temperature indicator: orange (LCM turned off when it’s below -25° C but the system functions normally)
(1) LED floodlight
(13) Keypad LED backlight

Button

(1) Factory-reset

NFC frequency

13.56 MHz

NFC read range

< 30 mm

NFC standards

ISO 14443A, 14443B, 15693

NFC technology

NFC Tag 1,2,3,4,5
MIFARE Classic
MIFARE Plus
MIFARE Ultralight
MIFARE DESFire

Ambient operating temperature

Device: -30 to 60° C (-22 to 140° F)
Display:* -25 to 60° C (-13 to 140° F)
*The display will turn off when the ambient temperature is above/below the display operation temperature, but other functions will remain functional. (Effective after firmware v 1.0.66)

Operating environment

Outdoor use

Ambient operating humidity

5 to 90% noncondensing

Software information

The software version of a product can be checked at https://unifi.ui.com

UL 294 level

Destructive attack: Level I
Line security: Level I
Endurance: Level I
Standby power: Level I

UL 294 statement

Compliance with IEEE 802.3 specifications was not verified as part of UL 294.
The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.

PoE cabling requirements

Cable 5e cabling is the minimum performance category recommended. The performance category utilized should match the transmission speed required at the installation site.
The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 26 AWG (0.13 mm ² ) for patch cords; 24 AWG (0.21 mm ² ) for horizontal or riser cable.

CAN/ULC-60839-11-1 Grade

Grade assignment: I

Certifications

CE, FCC, IC, UL 294, CAN/ULC-60839-11-1

Document number, and issue date and/or revision level

UA-Intercom, V01

UACC-Extender-2Wire-PoE-Tx/Rx
Mechanical

Dimensions

40 x 105 x 25 mm (1.6 x 4.1 x 1")

Weight

PoE in: 77 g (2.7 oz)
PoE out: 79 g (2.8 oz)

Enclosure material

Polycarbonate

Mounting material

Polycarbonate

Hardware

Networking interface

(1) 10/100 MbE
(1) Homeplug AV

Power method

PoE++

Max. power consumption

3W (Without PoE output)

PoE input

(1) PoE++, 50V DC, Max. 1.2A

PoE output

(1) PoE+, 48V DC, 0.72A

ESD/EMP protection

Air: ±8kV, contact: ±4kV

LED

White

Ambient operating temperature

-10 to 40° C (14 to 104° F)

Ambient operating humidity

5 to 95% noncondensing

Certifications

CE, FCC, IC

U-PoE++
Specifications

Model

U-PoE++

Dimensions

106 x 63 x 34 mm (4.2 x 2.5 x 1.3")

Weight

210 g (7.4 oz)

Output voltage

48V DC @ 1.25A

LAN activity indicator

No

Gigabit LAN port

Yes

Remote reset capability

No

Reset button

No

Rated voltage

100—240V AC @ 50/60Hz

Input current

1.3A @ 120V AC
0.75A @ 230V AC

Inrush current

<100A peak @ 120V AC
<200A peak @ 230V AC

Efficiency

85+%

Output ripple

1% max.

Switching frequency

65 kHz

Line regulation

≤ 1%

Load regulation

≤ 3%

2-pair powering

No

4-pair powering

Pins 1, 2, 4, 5 (+) and 3, 6, 7, 8 (-)

AC connector

IEC-320 C6

Data In / PoE

RJ45 shielded socket

Surge protection

Difference and common mode

Clamping protection

11V data, 60V power

Max. surge discharge

1500A (8/20 μs) power

Peak pulse current

36A (10/1000 μs) data

Shunt capacitance

<5 pF data

Response time

<1 ns

Power method

Universal AC input, 100—240V AC, 50/60 Hz

Power supply

AC/DC

Supported voltage range

100—240V AC

Max. PoE+ wattage per port by PSE

60W

Ambient operating temperature

0 to 40° C (32 to 104° F)

Storage temperature

-30 to 70°C (-22 to 158° F)

Ambient operating humidity

10 to 95% noncondensing

Certifications

CE, FCC, IC, UL, UKCA, KC, CCC, KC, RoHS
 

Software

Management application

UniFi Access: Version 2.1.5 and later
UniFi Protect: Version 4.0.33 and later